ZJSHUYI Debug sequence of soft starter.www.shuyitop.com; #softstarter

Debug sequence of soft starter: 1. Selection of starting mode and starting time of soft starter: ① For soft starters of general power, the larger the load, the longer the starting time; ② When the quality of power supply of the power grid is relatively high, the current limit start can be selected, and the same load The larger the value, the longer the startup time should be. 2. Check whether the motor can rotate normally and flexibly, otherwise it will never start. 3. Check the parameters of the fan, motor and soft starter. Parameters checked include voltage, current, power, and the number of poles of the motor. 4. The commissioning sequence is manual cranking, air-dropping control loop, motor idling, and running with load. 5. Check the insulation resistance of the motor. This work must be done before the motor is connected to the soft starter, because the starting circuit is composed of thyristor components. When the motor and the soft starter are connected, if the motor insulation resistance is measured with a high-voltage megohmmeter, the thyristor will be damaged. . www.shuyitop.com; Tel/Fax: 0086-577-62840011 WhatsApp: 008613355775769 #softstarter #motorsoftstar #softstarters #softstartechnology #solidstatesoftstarter #acmotorstarter

评论

发表评论

此博客中的热门博文

ZJSHUYI Maintenance requirements for frequency converters. www.shuyitop....

图片
Maintenance requirements in the day-to-day operation of the frequency converter 1. Check whether the cooling system is normal, and clean the dust of the air filter. 2. Check whether the screws, bolts and other fasteners of the inverter are loose, and perform necessary tightening; for the parts with soldering and crimping terminals, check whether there is corrosion, discoloration, cracks, damage, etc., and also check the frame Whether the structural parts are loose, whether the conductors and wires are damaged, etc. 3. Check whether the connection of the control circuit board is loose, whether the capacitor is leaking, whether the lines on the board are rusted, broken, etc. 4. Check whether the filter capacitor is leaking and whether the capacitance is reduced. 5. Check whether the insulation resistance is within the normal range. www.shuyitop.com; Tel/Fax: 0086-577-62840011 WhatsApp: 008613355775769 #VFD #INVERTER #frequencyinverter #frequencyconverter #shuyitop #converter ...
阅读全文

ZJSHUYI Usually the soft start system is composed of softstart device. w...

图片
Usually the soft start system is composed of softstart device, peripheral circuit and motor load. Therefore, the objects protected by the soft start system are also the soft start device, peripheral circuit and motor load. The purpose of protecting the soft start system is to ensure the safe and reliable operation of thyristor components, #softstarter equipment and circuits, and not damage or cause safety accidents under various abnormal working conditions. The premise of #softstarter protection is that the design of the soft starter itself should be correct. The thyristor components are correct and used correctly, the drive circuit and the control circuit are reasonably designed and matched with each other, so that the device can work in a good state. These measures are the basis for the safe and reliable operation of the soft starter. Only under this premise, can the devices, circuits, and equipment fail less and not fail from the inside, and the optimized system design should aim ...
阅读全文

ZJSHUYI Classic case of inverter maintenance failure.www.shuyitop.com; ...

图片
Foreword: Inverter repairers must keep in mind that the inverter module and the drive circuit are strongly related to failures. When the inverter module bursts and damages, the drive circuit is bound to be damaged by impact. The damage of the inverter module may also be caused by the failure of the drive circuit. Therefore, whether it is a failure of the drive circuit or the inverter output circuit, it must be The inverter output circuit and the drive circuit are thoroughly inspected together. The power-on test of the main circuit must be carried out under the premise that the drive circuit is normal and can output six excitation pulses normally. Inverter power failure A 132KW inverter has a black screen fault. Part of the wire drawing machine stopped in the wire drawing workshop, and restarted production after half a month. As a result, the inverter went black after being powered on. It was judged that the switching power supply was faulty on the spot. The inverter was removed, and th...
阅读全文