ZJSHUYI VFD AC single-phase inverter speed control drive.www.shuyitop.co...

Modern #frequencyconverters generally have a PI controller or PID controller inside. For closed-loop control systems such as constant pressure water supply, feedback signals (such as pressure signals) can be connected to the feedback signal terminal of the inverter, and the controller inside the #inverter can be used to achieve closed-loop control to reduce pressure deviation and maintain water pressure. constant. The main purpose of PLC is to control the number of pumps powered by the power frequency power supply based on the outlet pressure of the pipeline, and to provide start and stop commands to the frequency converter through the switch output signal, and to roughly adjust the total water supply of the pump station. In the system shown in the figure below, the pressure transmitter converts the water pressure of the outlet pipe of the pumping station into the voltage or current of the standard range, and these feedback quantities are directly sent to the analog input terminal of the #inverter. The frequency converter is integrated and has the advantages of low hardware cost, convenient use and less engineering programming. It should be used first. The pressure sensor that can be installed on the water pump outlet pipe can convert the pressure of 0-1MPa into a pressure of 4-20mA. DC current for closed loop control of water pressure. www.shuyitop.com; Tel/Fax: 0086-577-62840011 WhatsApp: 008613355775769 #inverter #forfrequencydrive #ACvfd #frequencyinverter #variablefrequencydrive #3phaseinputvariablefrequencydrive #variablefrequency #motoracinverter #acmotorspeedcontrollerdrive

评论

发表评论

此博客中的热门博文

ZJSHUYI Maintenance requirements for frequency converters. www.shuyitop....

图片
Maintenance requirements in the day-to-day operation of the frequency converter 1. Check whether the cooling system is normal, and clean the dust of the air filter. 2. Check whether the screws, bolts and other fasteners of the inverter are loose, and perform necessary tightening; for the parts with soldering and crimping terminals, check whether there is corrosion, discoloration, cracks, damage, etc., and also check the frame Whether the structural parts are loose, whether the conductors and wires are damaged, etc. 3. Check whether the connection of the control circuit board is loose, whether the capacitor is leaking, whether the lines on the board are rusted, broken, etc. 4. Check whether the filter capacitor is leaking and whether the capacitance is reduced. 5. Check whether the insulation resistance is within the normal range. www.shuyitop.com; Tel/Fax: 0086-577-62840011 WhatsApp: 008613355775769 #VFD #INVERTER #frequencyinverter #frequencyconverter #shuyitop #converter ...
阅读全文

ZJSHUYI Usually the soft start system is composed of softstart device. w...

图片
Usually the soft start system is composed of softstart device, peripheral circuit and motor load. Therefore, the objects protected by the soft start system are also the soft start device, peripheral circuit and motor load. The purpose of protecting the soft start system is to ensure the safe and reliable operation of thyristor components, #softstarter equipment and circuits, and not damage or cause safety accidents under various abnormal working conditions. The premise of #softstarter protection is that the design of the soft starter itself should be correct. The thyristor components are correct and used correctly, the drive circuit and the control circuit are reasonably designed and matched with each other, so that the device can work in a good state. These measures are the basis for the safe and reliable operation of the soft starter. Only under this premise, can the devices, circuits, and equipment fail less and not fail from the inside, and the optimized system design should aim ...
阅读全文

ZJSHUYI Classic case of inverter maintenance failure.www.shuyitop.com; ...

图片
Foreword: Inverter repairers must keep in mind that the inverter module and the drive circuit are strongly related to failures. When the inverter module bursts and damages, the drive circuit is bound to be damaged by impact. The damage of the inverter module may also be caused by the failure of the drive circuit. Therefore, whether it is a failure of the drive circuit or the inverter output circuit, it must be The inverter output circuit and the drive circuit are thoroughly inspected together. The power-on test of the main circuit must be carried out under the premise that the drive circuit is normal and can output six excitation pulses normally. Inverter power failure A 132KW inverter has a black screen fault. Part of the wire drawing machine stopped in the wire drawing workshop, and restarted production after half a month. As a result, the inverter went black after being powered on. It was judged that the switching power supply was faulty on the spot. The inverter was removed, and th...
阅读全文